plastic platform voltage capacitance voltage mark for 6.3v is 6v . lot no. positive negative u 1 z 2 s 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 l 11 1 12 g 13 b 14 configuration taping code capacitance tolerance ( + 20%) rated capacitance (10 f) rated voltage (16v) series name type x2 10 16v 0.3 max. 4.5 + 0.1 0.2 d + 0.5 b + 0.2 c + 0.2 0.5 max. a + 0.3 a + 0.3 e 0.5 to 0.8 zs series 4.5mml chip type chip type with 4.5mm height. designed for surface mounting on high density pc board. applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2002/95/ec). chip type type numbering system (example : 16v 10 f) specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) stability at low temperature endurance shelf life marking performance characteristics item 40 to + 85 c 4 to 50v 0.1 to 220f + 20% at 120hz, 20 c after 2 minutes' application of rated voltage , leakage current is not more than 0.01 cv or 3 (a) ,whichever is greater. black print on the case top. measurement frequency : 120hz , temperature : 20 c measurement frequency : 120hz the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 2000 hours at 85 c. after storing the capacitors under no load at 85 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. resistance to soldering heat the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20 c. zs bi-polarized zp wx zt z 25 c / z+20 c z 40 c / z+20 c rated voltage (v) impedance ratio zt / z20 (max.) 4 7 15 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 dimensions 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 220 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 101 221 4 4 5 6.3 28 33 56 96 4 5 5 6.3 28 37 45 70 5 5 6.3 33 41 52 4 5 6.3 6.3 23 37 49 58 4 5 6.3 6.3 16 27 42 52 4 5 6.3 18 29 46 4 4 4 4 4 4 4 5 6.3 1.0 2.0 2.8 4.0 8.4 13 17 20 33 rated ripple 4 0g 6.3 0j 10 1a 16 1c 25 1e 35 1v 50 1h v code rated ripple current (marms) at 85 c 120hz d a b c e 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 (mm) cap. (f) rated voltage (v) tan (max.) 4 0.50 6.3 0.30 10 0.24 16 0.19 25 0.16 35 0.14 50 0.14 capacitance change leakage current tan within + 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value capacitance change leakage current tan within + 20% of the initial capacitance value 200% or less than the initial specified value less than or equal to the initial specified value high temperature aluminum electrolytic capacitors zr smaller smaller taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please select ur(p.94), ug(p.100) series if high c/v products are reqired. please refer to page 3 for the minimum order quantity. case size d (mm) frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz or more 0.70 1.00 1.17 1.36 1.50 cat.8100y
|
